Go to the U of M home page
School of Physics & Astronomy
Assay and Acquisition of Radiopure Materials

User Tools

Trace: • tubes
vetoshield:tubes

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
vetoshield:tubes [2012/06/27 09:17] – [Preamp Cards] jeffvetoshield:tubes [2014/04/10 10:45] (current) – [Tube Repair, High and Low Voltage, Preamp cards] jeff
Line 1: Line 1:
 ===== Tube Repair, High and Low Voltage, Preamp cards ===== ===== Tube Repair, High and Low Voltage, Preamp cards =====
 +
 +====Tube Geometrical Specs=====
 +
 +{{:vetoshield:tufts_module.pdf|}}
 +
 +\\
 ====Preamp Cards==== ====Preamp Cards====
  
Line 7: Line 13:
 {{:vetoshield:broken_preamp_cards_updated_jul_28_2011_.xls|}} {{:vetoshield:broken_preamp_cards_updated_jul_28_2011_.xls|}}
  
 +\\
 ===Channel Schematic=== ===Channel Schematic===
 The following is a schematic of a SINGLE CHANNEL on a preamp card. Each preamp has two channels. The LS221 and SN75183 chips are each dual packaged so there is only one of each per card. The following is a schematic of a SINGLE CHANNEL on a preamp card. Each preamp has two channels. The LS221 and SN75183 chips are each dual packaged so there is only one of each per card.
Line 12: Line 19:
 {{:vetoshield:vetoshield_preamp_schematic.jpg?900}} {{:vetoshield:vetoshield_preamp_schematic.jpg?900}}
  
 +
 +===Low Voltage Connector===
 The P ground is the applied ground from the 15 pin low voltage connector. The S ground are the traces that run to the screw holes on the outside of the card and would normally be connected to the aluminum on the shield. The P ground is the applied ground from the 15 pin low voltage connector. The S ground are the traces that run to the screw holes on the outside of the card and would normally be connected to the aluminum on the shield.
  
 When looking at the preamp card with the 15 pin low voltage connector on the top the pinout is When looking at the preamp card with the 15 pin low voltage connector on the top the pinout is
  
-SSTTTTTGGGGGG77 +   ____card end_____ 
 +  | SSTTTTTGGGGGG77 | 
 +  |                 |
  
 where S and T represent +5S and +5T respectively, G represents ground and 7 represents -7 where S and T represent +5S and +5T respectively, G represents ground and 7 represents -7
  
-==Datasheets for the major components==+\\ 
 +===Charge Injection Test=== 
 +Scope screenshot below is of test with 250mV negative going pulse at 200khz repetition rate\\ 
 +Top trace is nput to TEST pin\\ 
 +Second trace shows signal at pin 3 of LM311\\ 
 +Third trace is +OUT\\ 
 +Fourth trace is -OUT\\ 
 +{{:vetodaq:vetopreamp_130225b.png?700}} 
 + 
 +\\ 
 +===Datasheets for the major components===
  
 {{:vetoshield:mpsh11_datasheet.pdf|}} {{:vetoshield:mpsh11_datasheet.pdf|}}
Line 31: Line 52:
  
 {{:vetoshield:sn75183_datasheet.pdf|}} {{:vetoshield:sn75183_datasheet.pdf|}}
 +====Low Voltage Distribution System====
 +
 +Below is a schematic of the low voltage distribution system for a given crate. 
 +
 +{{:vetoshield:low_voltage_distribution.jpg?1000|}}
 +
 +The original schematic file which can be edited is posted in the vetoshield ELOG https://fireplace.soudan.umn.edu:8082/Shield/ in entry # 486.
 +
 +===Breakout Box===
 +
 +Below is a more detailed representation of the breakout boxes being used
 +
 +{{:vetoshield:low_voltage_breakout_box.jpg?500|}}
 +
 +and some photos
 +
 +{{:vetoshield:bob1.jpg?500|}}{{:vetoshield:bob3.jpg?500|}}{{:vetoshield:bob4.jpg?500|}}{{:vetoshield:bob5.jpg?500|}}{{:vetoshield:bob6.jpg?500|}}
 +
 +
  
  
vetoshield/tubes.1340806672.txt.gz · Last modified: 2012/06/27 09:17 by jeff

Page Tools